I have been using Word for over 9 years and decided to get used to Open Office. I write in a journal and after several days of writing I would go back using WORD and select the dates like Monday Sept 1, 2010, Tuesday Sept 2, 2010 and maybe 20 other dates. Then by taking the cursor to the far left of the text (or date). The cursor in WORD would turn into an ARROW and allow me to select the ENTIRE line, I would then hold Control Key and move the arrow down the page clicking on each day and date. After selecting several dates, I would choose my Bottom Border, 3pt, Bold, and increase font to 16 point.ALL at the Same time. Is there a way to do this in Open Office. Thanks so much for your time in this manner, it will be very helpful. Michael in Tenn. Just to be clear: those are all multi-click actions, not a series of single-clicks. Best picture viewer for mac free. Double-click: select word, triple-click: select sentence, quad-click: select paragraph. You can hold the Ctrl key to make multiple selections, or use the 'ADD' selection mode (click the status bar, where it says 'STD', to cycle through the selection modes). Also, you do not need to select the whole paragraph to apply paragraph formatting, as long as Writer is clear that you mean to apply paragraph-level formatting. I would choose my Bottom Border, 3pt, Bold, and increase font to 16 point.ALL at the Same time. Split Selection into Lines - takes a contiguous selection and converts it to a multiple selection, one range for each line Ctrl/Cmd-B Add Next Match to Selection - adds the next match for the current range or word to the selection. Is there a way to do this in Open Office. This is a perfect example where using a style would save you far more time than selection voodoo. You can define a custom style in a few seconds and never have to repeat those formatting steps again. Edit: PPPS: Or, you could use the 'Format Paintbrush' and copy the formatting to each paragraph with just a click. All I'm trying to say is: it sounds like you're asking for help with pushing your car when all you have to do is start the engine. Michaelha7 wrote:i have been using Word for over 9 years and decided to get used to Open Office. I write in a journal and after several days of writing I would go back using WORD and select the dates like Monday Sept 1, 2010, Tuesday Sept 2, 2010 and maybe 20 other dates. Then by taking the cursor to the far left of the text (or date). The cursor in WORD would turn into an ARROW and allow me to select the ENTIRE line, I would then hold Control Key and move the arrow down the page clicking on each day and date. After selecting several dates, I would choose my Bottom Border, 3pt, Bold, and increase font to 16 point.ALL at the Same time. Is there a way to do this in Open Office. Thanks so much for your time in this manner, it will be very helpful. Michael in Tenn. Now I remember why I was not a Word fan. You can do most or all of this simply by apply a style. Have a look at the Style and Template chapters at. Most things are easier to do with styles in OOo. There are two ways to select a column within a table: • Position the insertion point in any cell within the column, display the Layout tab of the ribbon, then click Select| Select Column. • Move the mouse cursor just above the column you want to select. It will turn into a downward pointing arrow. Click on the left mouse button. The two ways to select a row within a table are very similar: • Position the insertion point in any cell within the row, display the Layout tab of the ribbon, then click Select| Select Row. • Move the mouse cursor just to the left of the row you want to select, and then click on the left mouse button. Selecting a column in a table depends on where the cursor is located and if you want just the data or the whole column. Move the mouse cursor to the top edge of the column you want to select. It will turn into a downward pointing arrow. Click on the left mouse button to select the data only, double click to get the data and header. Using the keyboard only: Select the Header cell and then Ctrl+Shift gets Header and Data. Select any other cell in the column and then Ctrl+Space selects the column of data, Ctrl+Space again to select the Header and Data.
0 Comments
Leave a Reply. |